Tools
- P5 Pentalobe Screwdriver Retina MacBook Pro and Air
- Suction Handle
- Opening Picks (Set of 6)
- Tweezers
- Spudger
- P2 Pentalobe Screwdriver iPhone
- T3 Torx Screwdriver
- T5 Torx Screwdriver
- TR8 Torx Security Screwdriver
Also check the tools for every linked access procedure. Match Torx and Torx Plus bits to the screw specified.
Parts and supplies
A complete display/lid assembly with frame, matched to the exact model, chip, size and finish. Confirm the included camera, cables and hinges.
Compare the exact model and part number before installation. Confirm all required screws, adhesive, tape, foam and fixtures in the complete procedure.
Exact-model documentationBefore you begin
Choose Apple menu → About This Mac and confirm the model, chip and screen size. For Intel 2020 MacBook Pro, also match the two-port or four-port version. A similar enclosure does not establish parts compatibility.
Battery and workspace precautions
Follow the discharge instruction in stage 1 before opening. A swollen, punctured, dented or unusually hot battery needs specialist handling. Do not bend, heat or force it. Protect your eyes, prevent accidental startup and disconnect power before adjusting any internal connection.
Repair sequence
Work through these stages with the complete illustrated procedure open. It contains the detailed screw map, torque values, connector directions and reassembly order for this model.
Open the complete illustrated procedureConfirm the part and prepare
Discharge the battery below 25% before opening. Back up your files, shut down, unplug all cables and work on a clean, ESD-safe surface.
Open the bottom and isolate power
Keep the lid closed while removing the bottom-cover screws and releasing its clips. Disconnect the battery power and data connections in the illustrated order before touching internal cables. Map every screw to its location.
Bottom cover access · detailed step 1Repair photo 1 of 2The original procedure uses some photos from a related model. Follow the exact-model instructions and screw map; small visual differences may appear. Battery connection · detailed step 8Repair photo 1 of 1The original procedure uses some photos from a related model. Follow the exact-model instructions and screw map; small visual differences may appear. Clear the display connections
Remove connector brackets, disconnect display and antenna cables, and remove the vent/antenna assembly and hinge covers. Protect sockets while releasing each connection.
Display connections · detailed step 15Repair photo 1 of 1The original procedure uses some photos from a related model. Follow the exact-model instructions and screw map; small visual differences may appear. Remove the complete lid
Support the display before releasing the hinge fasteners. Open the lid to the position illustrated, then lift or slide the hinges clear without catching the display cables.
Display assembly removal · detailed step 28Repair photo 1 of 1The original procedure uses some photos from a related model. Follow the exact-model instructions and screw map; small visual differences may appear. Display assembly · detailed step 31Repair photo 1 of 1The original procedure uses some photos from a related model. Follow the exact-model instructions and screw map; small visual differences may appear. Install and align the replacement
Match the complete assembly to the original. Seat the hinges and start their screws loosely. Align the closed lid evenly before final tightening; restore all antenna and display connections.
Reassemble and complete the repair
Restore all removed parts, covers and cable routes in the full procedure’s reassembly order. Reconnect battery power only at the specified stage, inspect for loose hardware, close the bottom and complete the checks below. Run the supported Repair Assistant or calibration process described in the manual.
Illustrated repair resources
MacBook Pro 13" Two Thunderbolt Ports 2020 Display Assembly Replacement
Carsten Frauenheim · 31 detailed steps
The original procedure uses some photos from a related model. Follow the exact-model instructions and screw map; small visual differences may appear.
Final checks
Use these checks after reassembly. Checkboxes reset when you leave the guide.
Prefer a professional repair?
Get help with diagnosis, parts compatibility or installation.
UWS organizes these repair stages and checks with credited repair resources. Follow the complete procedure for your exact hardware and replacement part. Available functions depend on part compatibility and any required calibration.