Ultimate Repair Hub · DIY Guide
iPhone 15 Back Glass Replacement
On the iPhone 15 the back glass is a separate panel held by adhesive, so it can be replaced without a laser machine.
- Difficulty
- ●●●○○Moderate
- Time
- 45–60 min
- Steps
- 11
- Opens from
- Back glass
DIY guide — for informational purposes only. This is not a substitute for professional diagnosis, and repairs are performed at your own risk. Ultimate Wireless Solutions is an independent repair provider and is not affiliated with Apple Inc.
Tools
- Pentalobe screwdriver P2
- Tri-point screwdriver Y000
- Heat pad, iOpener or heat gun on low
- Suction cup and thin plastic opening picks
- Nylon spudger and ESD-safe tweezers
- Isopropyl alcohol (90%+) and lint-free wipes
- Safety glasses and cut-resistant gloves if the glass is shattered
- Clamps or a screen press
Parts
- iPhone 15 back glass in your color
- Back glass adhesive
Removal
Power off and remove the bottom screws
Back up and power the phone off. Remove the two P2 pentalobe screws on either side of the USB-C port. Tape over cracked glass first so it doesn’t flake and the suction cup can grip.
Power off and remove the bottom screws1 photo · Tap image to enlarge Soften the adhesive
Warm the edges of the back glass evenly for 2–3 minutes. The glass should feel hot but still comfortable to hold.
Soften the adhesive1 photo · Tap image to enlarge Cut the back glass adhesive
Lift near the bottom edge with a suction cup and cut along both long sides and the top until the glass is free. Slide the glass slightly toward the bottom of the phone to release the top clips. Don’t lift the bottom edge more than about 5°.
Cut both long sides first, then slide the glass down slightly and cut the top. Open the back glass like a book
The back glass stays attached by a cable along one long edge, and that edge acts as the hinge. Lift the free edge and open it like a book. Support it, and cover the camera lenses to keep dust off.
Disconnect the battery first
Remove the 3 tri-point screws from the two connector covers. Unhook the lower cover by pushing it slightly toward the top of the phone, tilting it up and sliding it out toward the Taptic Engine. Release the upper cover by pressing its top edge about 1 mm toward the bottom of the phone, then lift it out from the bottom.
Unplug the battery cable first, then the back glass cable.
Disconnect the battery first3 photos · Tap image to enlarge Remove the old back glass
Set the old glass aside. If shards fell inside, wear safety glasses and cut-resistant gloves, pick them out with tweezers and wipe the frame edge with alcohol.
Remove the old back glass2 photos · Tap image to enlarge
Reassembly
Clean the frame and glass edges
Lift the old adhesive off the frame and pull it away at a low angle, then wipe with alcohol. Don’t touch the camera lenses.
Lay down the new adhesive
Peel the films from the new back glass, line up the adhesive, pull the bottom liner while pressing it down and run a spudger around the edge.
Lay down the new adhesive2 photos · Tap image to enlarge Connect the new back glass
Hold the new glass beside the phone in its open position. Connect the back glass cable first, then the battery cable, and refit both covers and their 3 tri-point screws.
Connect the new back glass4 photos · Tap image to enlarge Close and press
Peel the remaining liners, check the magnets for stray screws, close the glass, press the edges until flush and clamp it for several minutes. Reinstall the bottom screws.
Close and press2 photos · Tap image to enlarge Test wireless charging
Test MagSafe or wireless charging, the flashlight and all rear cameras.
Cracked back? We’ll swap it today.
Bring your iPhone 15 to our Tustin store for a same-day back glass replacement.
Facts checked against Apple’s iPhone 15 repair manual. These guides are for informational purposes and repairs are done at your own risk. Ultimate Wireless Solutions is an independent repair shop and is not affiliated with Apple Inc.
