---
title: "Galaxy S25 Plus Screen Replacement Guide | Ultimate Wireless"
description: "Screen Replacement for the Galaxy S25+: tools, parts and 13 steps from our Tustin repair techs. Buy the parts, or book same-day repair in Orange County."
canonical: https://ultimatewirelesssolutions.com/repair-guides/samsung/galaxy-s25-plus/screen-replacement
---

Ultimate Repair Hub · DIY Guide

# Galaxy S25+ Screen Replacement

On the Galaxy S25+ we only sell the screen already fitted in a new frame. Samsung bonds the curved screen to the frame, and trying to separate them usually breaks the new one. Instead, everything inside your phone moves over to the new frame.

[Get Parts](https://ultimatewirelesssolutions.com/repair-parts?brand=samsung&model=galaxy-s25-plus)[Book Professional Repair](https://ultimatewirelesssolutions.com/appointment)[Request Quote](https://ultimatewirelesssolutions.com/get-a-quote)

Difficulty

●●●●●Very difficult

Time

2–3 hours

Steps

13

Opens from

Back glass (everything moves to a new frame)

1.  [Home](https://ultimatewirelesssolutions.com/) ›
2.  [DIY Repair Guides](https://ultimatewirelesssolutions.com/repair-guides) ›
3.  [Samsung Galaxy](https://ultimatewirelesssolutions.com/repair-guides/samsung) ›
4.  [Galaxy S25+](https://ultimatewirelesssolutions.com/repair-guides/samsung/galaxy-s25-plus) ›
5.  Screen Replacement

**DIY guide — for informational purposes only.** This is not a substitute for professional diagnosis, and repairs are performed at your own risk. Ultimate Wireless Solutions is an independent repair provider and is not affiliated with Apple Inc.

## Tools

-   Phillips screwdriver #00
-   SIM eject tool
-   Heat pad, iOpener or heat gun on low
-   Suction cup and thin plastic opening picks
-   Nylon spudger and ESD-safe tweezers
-   Isopropyl alcohol (90%+) and lint-free wipes
-   A thin plastic card (never metal) for lifting the battery
-   Clamps or a screen press
-   Safety glasses, and a metal can of sand for the old battery

## Parts

-   Galaxy S25+ screen with frame in your color
-   New Galaxy S25+ battery (recommended, because the old one usually bends coming out)
-   Back glass adhesive

**Advanced repair.** Keep every screw in order on a magnetic mat; a long screw in the wrong hole can damage the logic board.

**Before you start:** run the battery down below 25%. Less charge means much less stored energy if the cell is damaged. If the battery is swollen, dented or punctured at any point, stop and bring the phone to a shop.

**Fingerprint:** After the repair, register your fingerprint again. Some aftermarket and refurbished screens don’t support the under-screen fingerprint reader; face unlock and PIN still work.

## Table of contents

1.  [1. Open the back](#phase-0)
2.  [2. Move everything to the new frame](#phase-1)
3.  [3. Reassembly](#phase-2)

## Open the back

1.  1
    
    ### Power off and remove the SIM tray
    
    Power off the phone and pull the SIM tray. Samsung back glass is thin and bonds hard, so cover it with packing tape if it’s cracked.
    
2.  2
    
    ### Heat the back glass
    
    Warm the edges of the back glass evenly for 3–5 minutes. Samsung uses stronger adhesive than Apple, so expect to reheat a couple of times. Keep the heat moving and away from the camera lenses.
    
3.  3
    
    ### Cut the back glass adhesive
    
    Lift near the bottom edge with a suction cup just enough for a hairline gap, slide a pick in and work it around all four sides, leaving picks in the gap so the adhesive doesn’t reseal. Keep the pick shallow at the top near the cameras.
    
    There is no cable attached to the back glass on these phones, so once the adhesive is cut the glass lifts straight off.
    
    Cut both long sides first, then slide the glass down slightly and cut the top.
    
4.  4
    
    ### Remove the wireless charging cover
    
    Remove the Phillips screws around the top plastic cover (it carries the wireless charging and NFC coil) and lift it off. Some models have a bottom cover over the speaker too; remove its screws and lift it off.
    
5.  5
    
    ### Disconnect the battery
    
    Unplug the **battery cable first** with the flat end of a spudger, before you touch any other cable. Then unplug the long main cable that crosses the battery and links the logic board to the charging port board.
    
    Battery off first and back on last, so the phone stays dead while cables are moving. Schematic, not to scale.
    

## Move everything to the new frame

1.  6
    
    ### Lift out the boards and cameras
    
    Unplug the display cable, the antenna cables and the camera cables from the logic board, remove its Phillips screws and lift the board out by its edges. Lift the rear cameras out of the frame. Then unplug and remove the charging port board at the bottom and the loudspeaker.
    
2.  7
    
    ### Move the small parts
    
    Move the vibration motor, the earpiece if it isn’t on the logic board, any rubber gaskets and the antenna cables over to the new frame. Check the new frame has its side buttons fitted; if it doesn’t, move the button cable across too.
    
3.  8
    
    ### Soften the battery adhesive
    
    The battery is glued to the frame with no pull tabs on most of these models. Drip isopropyl alcohol along the edges of the battery and let it soak in for a minute or two. If your battery does have pull tabs, use them instead.
    
4.  9
    
    ### Lift the battery out
    
    Starting from the bottom edge, slide a plastic card under the battery and lift slowly, adding alcohol as you go. Never use metal, never bend the cell, and stop if it swells, smokes or smells. Put the old battery straight into a metal can of sand.
    
5.  10
    
    ### Fit a new battery in the new frame
    
    A battery that has been pried out is often bent, so use a new one. Apply fresh adhesive and press the battery into the new frame.
    

## Reassembly

1.  11
    
    ### Rebuild in the new frame
    
    Fit the charging port board, the loudspeaker, the logic board and the cameras into the new frame in the same order they came out. Reconnect every cable, then plug in the main cable and the **battery last**. Refit the covers and their screws.
    
2.  12
    
    ### Test before you close
    
    Power on and check the screen, touch, both cameras, the speakers, charging and the side buttons. Re-register your fingerprint in Settings.
    
3.  13
    
    ### Close the back
    
    Clean the back glass, lay new back glass adhesive, press the glass onto the new frame and clamp it for several minutes. Slide the SIM tray back in.
    

## Rather not do a frame swap?

We replace Galaxy S25+ screens at our Tustin shop, usually the same day, with a warranty on parts and labor.

[Book Professional Repair](https://ultimatewirelesssolutions.com/appointment)[Request Quote](https://ultimatewirelesssolutions.com/get-a-quote)

Written by our Tustin repair techs. These guides are for informational purposes and repairs are done at your own risk. Ultimate Wireless Solutions is an independent repair shop and is not affiliated with Apple Inc.

Parts for this repair

### Galaxy S25+ Screen

Comes already fitted in a new frame in your color

Add the repair tool set (optional)P2 pentalobe, Y000 tri-point and Phillips screwdrivers, pry tools, picks and a suction cup+$5.99

$103screen only

Ships from or pick up at our Tustin store; shipping options and costs are shown at checkout.

### Want us to do it?

Same-day Galaxy S25+ screen replacement in Tustin. Call or text:

[949-300-8898](tel:9493008898)[Or text us](sms:9493008898)

---

Ultimate Wireless Solutions · 18062 Irvine Blvd Suite 207, Tustin, CA 92780 · (949) 300-8898 · https://ultimatewirelesssolutions.com
