--- title: "MacBook Pro 14-inch PROLED XDR (M5 Pro / M5 Max, 2026) Screen Repair" description: "Screen Replacement (with Frame) for MacBook Pro 14-inch PROLED XDR (M5 Pro / M5 Max, 2026): preparation, tools, repair steps, inline photos and diagrams, and final checks." canonical: https://ultimatewirelesssolutions.com/repair-guides/apple/macbook-pro-14-proled-m5-pro-max-2026/screen-replacement --- Ultimate Repair Hub · DIY Guide # MacBook Pro 14-inch PROLED XDR (M5 Pro / M5 Max, 2026) Screen Replacement (with Frame) Guide Replace the complete display assembly, including the lid and frame. Confirm the exact MacBook model before ordering parts or opening the computer. [Check Parts Availability](https://ultimatewirelesssolutions.com/get-a-quote)[Book Professional Repair](https://ultimatewirelesssolutions.com/appointment)[Request Quote](https://ultimatewirelesssolutions.com/get-a-quote) Difficulty Advanced Repair sequence 6 stages Final checks 4 checks Opens from Bottom cover 1. [Home](https://ultimatewirelesssolutions.com/) › 2. [DIY Repair Guides](https://ultimatewirelesssolutions.com/repair-guides) › 3. [Apple MacBook](https://ultimatewirelesssolutions.com/repair-guides/macbook) › 4. [MacBook Pro 14-inch PROLED XDR (M5 Pro / M5 Max, 2026)](https://ultimatewirelesssolutions.com/repair-guides/apple/macbook-pro-14-proled-m5-pro-max-2026) › 5. Screen Replacement (with Frame) ## Tools - Adjustable torque driver (10–34 Ncm) - Battery cover - Cut-resistant gloves - ESD-safe tweezers - Microterry polishing cloth - Nylon probe (black stick) - Pentalobe screwdriver - Permanent marker - Suction cup - Torque driver (blue, 0.65 kgf cm) - Torx Plus 3IP 44 mm half-moon bit - Torx Plus 5IP 50 mm bit - Adjustable torque driver (0.3–1.2 Nm) - Torx Plus 8IP 25 mm bit Also check the tools for every linked access procedure. Match Torx and Torx Plus bits to the screw specified. ## Parts and supplies A complete display/lid assembly with frame, matched to the exact model, chip, size and finish. Confirm the included camera, cables and hinges. Compare the exact model and part number before installation. Confirm all required screws, adhesive, tape, foam and fixtures in the complete procedure. [Exact-model documentation](https://support.apple.com/en-us/docs/mac/301343) ## Table of contents 1. [1. Before you begin](#prepare) 2. [2. Repair sequence](#steps) 3. [3. Illustrated resources](#walkthrough) 4. [4. Final checks](#checks) ## Before you begin Choose Apple menu → About This Mac and confirm the model, chip and screen size. For Intel 2020 MacBook Pro, also match the two-port or four-port version. A similar enclosure does not establish parts compatibility. Battery and workspace precautions Follow the discharge instruction in stage 1 before opening. A swollen, punctured, dented or unusually hot battery needs specialist handling. Do not bend, heat or force it. Protect your eyes, prevent accidental startup and disconnect power before adjusting any internal connection. [Battery safety and workspace setup](https://support.apple.com/en-us/100353) Select the PROLED XDR assembly for this exact model. Inspect the display cable mandrels and use the linked mandrel repair procedure if they are damaged. ## Repair sequence Work through these stages with the complete illustrated procedure open. It contains the detailed screw map, torque values, connector directions and reassembly order for this model. [Open the complete illustrated procedure](https://support.apple.com/en-us/148436) 1. 1 ### Confirm the part and prepare Discharge the battery fully, following the exact-model safety procedure, before opening. Back up your files, shut down, unplug all cables and work on a clean, ESD-safe surface. 2. 2 ### Open the bottom and isolate power Keep the lid closed while removing the bottom-cover screws and releasing its clips. Disconnect the battery power and data connections in the illustrated order before touching internal cables. Map every screw to its location. Bottom cover removal reference 1Apple diagram 1 of 2 ![MacBook Pro (14-inch PROLED XDR, M5 Pro or M5 Max) Bottom Case Removal: Bottom cover removal reference 1 (apple diagram)](https://cdsassets.apple.com/live/SZLF0YNV/service-documentation/macbook-pro/148409-148410/148409_Bottom_Case_REM_Four_Screws.png) Bottom cover removal reference 1 3. 3 ### Complete the access steps Complete these linked procedures in order: Vent/antenna module; Display hinge covers. Preserve cable routing and keep the battery protected during each step. [Bottom case](https://support.apple.com/en-us/148409)[Vent/antenna module](https://support.apple.com/en-us/148424)[Display hinge covers](https://support.apple.com/en-us/148427) 4. 4 ### Release and remove the display Disconnect the three display/camera flexes. Unclip both cable supports and mandrels without levering on the logic board. Support the lid, remove six hinge screws and lift the assembly clear. Display removal reference 1Apple diagram 1 of 5 ![MacBook Pro (14-inch PROLED XDR, M5 Pro or M5 Max) Display Removal: Display removal reference 1 (apple diagram)](https://cdsassets.apple.com/live/SZLF0YNV/service-documentation/macbook-pro/148436-148437/148436_Display_REM_Remove_Three_3IP_Screws.png) Display removal reference 1 5. 5 ### Install the complete display Position the hinges, loosely install their screws, and align the closed lid flush. Tighten to the manual’s torque. Refit the mandrels, cable clips, three flexes and connector cowling. 6. 6 ### Reassemble and complete the repair Restore all removed parts, covers and cable routes in the full procedure’s reassembly order. Reconnect battery power only at the specified stage, inspect for loose hardware, close the bottom and complete the checks below. Run the supported Repair Assistant or calibration process described in the manual. ## Illustrated repair resources ### MacBook Pro (14-inch PROLED XDR, M5 Pro or M5 Max) Display Removal Apple [Complete illustrated procedure](https://support.apple.com/en-us/148436)[Complete reassembly procedure](https://support.apple.com/en-us/148437)[Complete Apple repair manual](https://support.apple.com/en-us/149399)[Repair Assistant](https://support.apple.com/en-us/100350#Software)[Repairing Damaged Display Mandrels](https://support.apple.com/en-us/148622) ## Final checks Use these checks after reassembly. Checkboxes reset when you leave the guide. Check a solid white, black and colored image for lines, dark areas and flicker. Test brightness and supported display modes.Test the camera, ambient-light response and any supported touch input. Check Wi-Fi and Bluetooth after antenna reconnection.Open and close the lid slowly. Confirm even alignment, smooth hinges, sleep and wake, with no trapped cables.Complete the repair software steps specified for this exact model. Test keyboard, trackpad, Touch ID, speakers and charging. ## Prefer a professional repair? Get help with diagnosis, parts compatibility or installation. [Book Professional Repair](https://ultimatewirelesssolutions.com/appointment)[Request Quote](https://ultimatewirelesssolutions.com/get-a-quote) UWS organizes these repair stages and checks with credited repair resources. Follow the complete procedure for your exact hardware and replacement part. Available functions depend on part compatibility and any required calibration. Parts for this repair ### MacBook Pro 14-inch PROLED XDR (M5 Pro / M5 Max, 2026) Ask us to confirm the correct part and availability before ordering. [Check Parts Availability](https://ultimatewirelesssolutions.com/get-a-quote) ### Want us to do it? MacBook repair help in Tustin. Call or text: [949-300-8898](tel:9493008898)[Or text us](sms:9493008898) 18062 Irvine Blvd, Suite 207 Tustin, CA 92780 ### More for this MacBook [Battery Replacement →](https://ultimatewirelesssolutions.com/repair-guides/apple/macbook-pro-14-proled-m5-pro-max-2026/battery-replacement)[All MacBook guides →](https://ultimatewirelesssolutions.com/repair-guides/macbook) --- Ultimate Wireless Solutions · 18062 Irvine Blvd Suite 207, Tustin, CA 92780 · (949) 300-8898 · https://ultimatewirelesssolutions.com