---
title: "iPhone SE (3rd generation) Charge Port Guide | Ultimate Wireless"
description: "Charge Port Replacement for the iPhone SE (3rd generation): tools, parts and 6 steps from our Tustin repair techs. Buy the parts, or book same-day repair in Orange County."
canonical: https://ultimatewirelesssolutions.com/repair-guides/apple/iphone-se-3rd-generation/charge-port-replacement
---

Ultimate Repair Hub · DIY Guide

# iPhone SE (3rd generation) Charge Port Replacement

This is an advanced repair on the iPhone SE (3rd generation): the screen and the parts at the bottom of the phone come out, and so does the logic board to reach the Lightning port. Before you start, clean lint out of the port with a wooden toothpick and try another cable; most charging problems aren’t the port.

[Get Parts](https://ultimatewirelesssolutions.com/repair-parts?brand=apple&model=iphone-se-3rd-generation)[Book Professional Repair](https://ultimatewirelesssolutions.com/appointment)[Request Quote](https://ultimatewirelesssolutions.com/get-a-quote)

Difficulty

●●●●●Very difficult

Time

2–3 hours

Steps

6

Opens from

Front (screen)

1.  [Home](https://ultimatewirelesssolutions.com/) ›
2.  [DIY Repair Guides](https://ultimatewirelesssolutions.com/repair-guides) ›
3.  [Apple iPhone](https://ultimatewirelesssolutions.com/repair-guides/apple) ›
4.  [iPhone SE (3rd generation)](https://ultimatewirelesssolutions.com/repair-guides/apple/iphone-se-3rd-generation) ›
5.  Charge Port Replacement

**DIY guide — for informational purposes only.** This is not a substitute for professional diagnosis, and repairs are performed at your own risk. Ultimate Wireless Solutions is an independent repair provider and is not affiliated with Apple Inc.

## Tools

-   Pentalobe screwdriver P2
-   Phillips screwdriver #000
-   Tri-point screwdriver Y000
-   Heat pad, iOpener or heat gun on low
-   Suction cup and thin plastic opening picks
-   Blunt tweezers
-   Nylon spudger and ESD-safe tweezers
-   Isopropyl alcohol (90%+) and lint-free wipes
-   Clamps or a screen press

## Parts

-   iPhone SE (3rd generation) Lightning port assembly
-   Pre-cut display adhesive

**Advanced repair.** Keep every screw in order on a magnetic mat; a long screw in the wrong hole can damage the logic board.

**Before you start:** run the battery down below 25%. Less charge means much less stored energy if the cell is damaged. If the battery is swollen, dented or punctured at any point, stop and bring the phone to a shop.

## Take it apart and replace the port

1.  1
    
    ### Open the screen and disconnect the battery
    
    Follow our screen guide to open the display, unplug the battery cable first, then the display cables, and set the display aside.
    
2.  2
    
    ### Remove the speaker and Taptic Engine
    
    Remove the screws from the bottom speaker and the Taptic Engine, unplug the Taptic Engine and lift both out. The battery can stay in place; it only needs to be disconnected.
    
3.  3
    
    ### Lift out the logic board
    
    On this model the Lightning cable runs under the logic board, so the board has to come out. Remove the rear camera, pull the SIM tray, unplug every cable and antenna on the board, remove its screws and lift it out by its edges. Take a photo first so every screw goes back in the same hole.
    
4.  4
    
    ### Remove the port
    
    Remove the screws on either side of the Lightning port and any small brackets over its cable, then peel the cable off the frame where it’s stuck down and lift the port assembly out. It includes the bottom microphones.
    
5.  5
    
    ### Fit the new port
    
    Set the new port in place and line it up with the opening (a Lightning cable plugged in from outside, not connected to power, helps). Press its cable onto the frame and reinstall the screws and brackets.
    
6.  6
    
    ### Rebuild and test
    
    Refit everything you removed, reconnect the cables with the battery last and close with fresh display adhesive. Test charging, data to a computer, both bottom microphones (record a voice memo and make a call) and the speaker.
    

## Not charging? Let us look first.

Most iPhone SE (3rd generation) charging problems are lint or a bad cable. We’ll test it free at our Tustin store and replace the port the same day if needed.

[Book Professional Repair](https://ultimatewirelesssolutions.com/appointment)[Request Quote](https://ultimatewirelesssolutions.com/get-a-quote)

Written by our Tustin repair techs. These guides are for informational purposes and repairs are done at your own risk. Ultimate Wireless Solutions is an independent repair shop and is not affiliated with Apple Inc.

Tools for this repair

### Repair Tool Set

The tools for this guide. Charge port parts are available in store; call us for pricing.

Repair Tool Set (10-piece) · $5.99P2 pentalobe, Y000 tri-point and Phillips screwdrivers, pry tools, picks and a suction cup

$5.99tool set

Ships from or pick up at our Tustin store; shipping options and costs are shown at checkout.

### Want us to do it?

Same-day iPhone SE (3rd generation) charge port replacement in Tustin. Call or text:

[949-300-8898](tel:9493008898)[Or text us](sms:9493008898)

---

Ultimate Wireless Solutions · 18062 Irvine Blvd Suite 207, Tustin, CA 92780 · (949) 300-8898 · https://ultimatewirelesssolutions.com
