Ultimate Repair Hub · DIY Guide
iPhone SE (3rd generation) Battery Replacement
On the iPhone SE (3rd generation) the battery comes out through the front: the screen opens first, then stretch-release adhesive strips let go of the battery when you pull them slowly.
- Difficulty
- ●●●○○Moderate
- Time
- 45–75 min
- Steps
- 14
- Opens from
- Front (screen)
DIY guide — for informational purposes only. This is not a substitute for professional diagnosis, and repairs are performed at your own risk. Ultimate Wireless Solutions is an independent repair provider and is not affiliated with Apple Inc.
Tools
- Pentalobe screwdriver P2
- Phillips screwdriver #000
- Tri-point screwdriver Y000
- Heat pad, iOpener or heat gun on low
- Suction cup and thin plastic opening picks
- Blunt tweezers (for the adhesive strips)
- Nylon spudger and ESD-safe tweezers
- Isopropyl alcohol (90%+) and lint-free wipes
- A thin plastic card (never metal) for lifting the battery
- Clamps or a screen press
- Safety glasses, and a metal can of sand for the old battery
Parts
- iPhone SE (3rd generation) replacement battery (adhesive included)
- Pre-cut display adhesive
Open the screen
Power off and remove the bottom screws
Back up and power the phone off. Remove the two P2 pentalobe screws on either side of the Lightning port. If the screen is cracked, cover it with packing tape first so glass doesn’t flake and the suction cup can grip.
Bottom edge. One screw on each side of the port. Soften the adhesive
Warm the edges of the screen evenly for 2–3 minutes. The glass should feel hot but still comfortable to hold.
Cut the adhesive around the sides and top
Put the suction cup just above the home button, not on it, and lift just enough for a hairline gap. Slide a pick in and cut along both long sides. Keep the pick shallow, a few millimeters at most, so you don’t catch the display cables.
The top edge is held by plastic clips, so don’t pry it. Slide the display a millimeter or two toward the bottom of the phone to release the clips, then cut across the top. Don’t lift the bottom edge more than about 5°.
Cut both long sides first, then slide the screen down slightly and cut the top. Open the display like a book
The display stays attached by short cables along one long edge, and that edge acts as the hinge. Lift the free edge, open it to about 90° and lean it on something sturdy so the cables aren’t holding its weight.
Disconnect the battery, then the display
Remove the Phillips screws from the lower connector bracket and lift it off. Keep the screws in order; they are different lengths.
Unplug the battery cable first, then the two display cables. Remove the Phillips screws from the small upper bracket and unplug the front camera and sensor cable.
Battery off first and back on last, so the phone stays dead while cables are moving. Schematic, not to scale. Set the display aside
Lift the display away and lay it face down on a clean, soft surface.
Remove the battery
Remove the Taptic Engine
Remove the Phillips screws holding the Taptic Engine, unplug its cable and lift it out. It sits over the bottom ends of the battery adhesive strips.
Pull the adhesive strips
Peel the first tab off the battery with blunt tweezers without scraping the cell, wrap it around the tweezers and lift until white adhesive shows.
Keep the tweezers low and nearly parallel to the battery and pull slowly toward the top of the phone, twisting as you go, until the whole strip slides out. Repeat for each strip. Pulling fast or at a steep angle is what snaps them.
If a strip snaps
Grab a visible broken end and keep twisting. If it’s out of reach, drip a little isopropyl alcohol under that side of the battery, wait a minute, then lift slowly with a plastic card. Never use metal, never bend the battery, and stop if it starts to swell, smoke or smell.
Lift the battery out
Lift the battery from the frame and put it straight into a metal can of sand.
Install and close
Clean the battery bay
Wipe away any leftover adhesive with isopropyl alcohol and check the bay for loose screws, which can puncture the new cell.
Seat the new battery
Stick the new adhesive strips on the battery (or peel the liner if they’re pre-applied), line the battery up and press it down firmly across the whole cell. Leave the pull tabs free so the next person can get it out.
Rebuild and close
Reinstall the Taptic Engine and its screws. Reconnect the display cables, then the battery last, and refit the brackets. Lay fresh display adhesive, close and clamp the screen, and reinstall the bottom screws.
Test and finish
Charge for a few minutes before powering on. On many of these models iOS shows an “Important Battery Message” or “Unknown Part” for any battery not fitted by Apple, and Battery Health may not show a percentage. The battery still works normally.
Want it done in 30 minutes?
Bring your iPhone SE (3rd generation) to our Tustin store. We handle the battery disposal and the screen seal for you.
Written by our Tustin repair techs. These guides are for informational purposes and repairs are done at your own risk. Ultimate Wireless Solutions is an independent repair shop and is not affiliated with Apple Inc.
