---
title: "iPhone 17e Back Glass Replacement Guide | Ultimate Wireless"
description: "Back Glass Replacement for the iPhone 17e: tools, parts and 11 steps from our Tustin repair techs. Buy the parts, or book same-day repair in Orange County."
canonical: https://ultimatewirelesssolutions.com/repair-guides/apple/iphone-17e/back-glass-replacement
---

Ultimate Repair Hub · DIY Guide

# iPhone 17e Back Glass Replacement

On the iPhone 17e the back glass is a separate panel held by adhesive, so it can be replaced without a laser machine.

[Get Parts](https://ultimatewirelesssolutions.com/repair-parts?brand=apple&model=iphone-17e)[Book Professional Repair](https://ultimatewirelesssolutions.com/appointment)[Request Quote](https://ultimatewirelesssolutions.com/get-a-quote)

Difficulty

●●●○○Moderate

Time

45–60 min

Steps

11

Opens from

Back glass

1.  [Home](https://ultimatewirelesssolutions.com/) ›
2.  [DIY Repair Guides](https://ultimatewirelesssolutions.com/repair-guides) ›
3.  [Apple iPhone](https://ultimatewirelesssolutions.com/repair-guides/apple) ›
4.  [iPhone 17e](https://ultimatewirelesssolutions.com/repair-guides/apple/iphone-17e) ›
5.  Back Glass Replacement

**DIY guide — for informational purposes only.** This is not a substitute for professional diagnosis, and repairs are performed at your own risk. Ultimate Wireless Solutions is an independent repair provider and is not affiliated with Apple Inc.

## Tools

-   Pentalobe screwdriver P2
-   Tri-point screwdriver Y000
-   Heat pad, iOpener or heat gun on low
-   Suction cup and thin plastic opening picks
-   Nylon spudger and ESD-safe tweezers
-   Isopropyl alcohol (90%+) and lint-free wipes
-   Safety glasses and cut-resistant gloves if the glass is shattered
-   Clamps or a screen press

## Parts

-   iPhone 17e back glass in your color
-   Back glass adhesive

**Shattered glass:** cover the whole back with packing tape before you start and wear safety glasses.

## Table of contents

1.  [1. Removal](#phase-0)
2.  [2. Reassembly](#phase-1)

## Removal

1.  1
    
    ### Power off and remove the bottom screws
    
    Back up and power the phone off. Remove the two pentalobe screws on either side of the USB-C port. If the glass is cracked, cover it with packing tape first so it doesn’t flake and the suction cup can grip.
    
    Bottom edge. One screw on each side of the port.
    
2.  2
    
    ### Soften the adhesive
    
    Warm the edges of the back glass evenly for 2–3 minutes. The glass should feel hot but still comfortable to hold.
    
3.  3
    
    ### Cut the back glass adhesive
    
    Lift near the bottom edge with a suction cup just enough for a hairline gap, slide a pick in and cut up both long sides, stopping at the antenna lines. Pull the glass slightly toward you to free the hooks along the top, then cut across the top.
    
    Don’t lift the bottom edge more than about 5°; the cables there are short.
    
    Cut both long sides first, then slide the glass down slightly and cut the top.
    
4.  4
    
    ### Open the back glass like a book
    
    The back glass stays attached by a cable along one long edge, and that edge acts as the hinge. Lift the free edge and open it like a book. Support it so the cable isn’t holding its weight, and cover the camera lenses to keep dust off.
    
5.  5
    
    ### Disconnect the battery first
    
    Remove the 3 tri-point screws from the middle and lower connector covers and lift them off. Unplug the **battery cable first**, then the back glass cable. The battery cable has strong adhesive under it, so lift it gently.
    
    Battery off first and back on last, so the phone stays dead while cables are moving. Schematic, not to scale.
    
6.  6
    
    ### Remove the old back glass
    
    Set the old glass aside. If shards fell inside, wear safety glasses and cut-resistant gloves, pick them out with tweezers and wipe the frame edge with alcohol.
    

## Reassembly

1.  7
    
    ### Clean the frame
    
    Lift the old adhesive off the frame and wipe the edge with isopropyl alcohol. Don’t touch the camera lenses.
    
2.  8
    
    ### Lay down the new adhesive
    
    Peel the films from the new back glass, line up the new adhesive, pull the bottom liner while pressing it down and run a spudger around the edge.
    
3.  9
    
    ### Connect the new back glass
    
    Hold the new glass beside the phone in its open position. Connect the back glass cable first, then the battery cable, and refit the covers and their screws.
    
4.  10
    
    ### Close and press
    
    Peel the remaining liners, check the magnets for stray screws, close the glass, press the edges until flush and clamp it for several minutes. Reinstall the bottom screws.
    
5.  11
    
    ### Test wireless charging
    
    Test MagSafe or wireless charging, the flashlight and the rear camera.
    

## Cracked back? We’ll swap it today.

Bring your iPhone 17e to our Tustin store for a same-day back glass replacement.

[Book Professional Repair](https://ultimatewirelesssolutions.com/appointment)[Request Quote](https://ultimatewirelesssolutions.com/get-a-quote)

Facts checked against Apple’s iPhone 17e repair manual. These guides are for informational purposes and repairs are done at your own risk. Ultimate Wireless Solutions is an independent repair shop and is not affiliated with Apple Inc.

Parts for this repair

### iPhone 17e Back Glass

Pick your color

Add the repair tool set (optional)P2 pentalobe, Y000 tri-point and Phillips screwdrivers, pry tools, picks and a suction cup+$5.99

$44black back glass only

Ships from or pick up at our Tustin store; shipping options and costs are shown at checkout.

### Want us to do it?

Same-day iPhone 17e back glass replacement in Tustin. Call or text:

[949-300-8898](tel:9493008898)[Or text us](sms:9493008898)

---

Ultimate Wireless Solutions · 18062 Irvine Blvd Suite 207, Tustin, CA 92780 · (949) 300-8898 · https://ultimatewirelesssolutions.com
